Installing Click Lock flooring can be very simple if you take your time and follow the 4 correct steps. When installing any flooring, it is essential to follow the manufacturer’s instructions to ensure everything goes smoothly.
What you’ll need
Before you begin the process of installing Click Lock flooring, you’ll need to make sure you have all the necessary tools and materials on hand.
First, you will need a good quality utility knife for cutting the tiles to size. A suitable cutting mat is also an excellent investment to help protect your work surface.
You will also need a hammer to tap the locking strips into place and a pair of rubber gloves to protect your hands while hammering the locking strips.
You may also be required to have a spirit level depending on the layout of the floor.
Finally, you will need a suitable adhesive for the subfloor, a suitable underlay, and a Click Lock Joint tape roll. Click Lock Joint tape joins the tiles to form a solid floor covering.
Installing Click Lock Flooring: The Basics
The first step in installing Click Lock flooring is to measure the area you will tile. If you cover a whole floor and do not have a pre-existing subfloor, you will need to lay a new one. For laying a new subfloor, you can use various materials, including plywood, chipboard, or tiles.
The most important thing is to ensure that the subfloor is level and strong enough to support the weight of the tiles. If you are tiling over an existing floor, you can use a floor scraper or a putty removal tool to remove any remaining glue. Cut your tiles to the correct length and width, and then use an adhesive to attach them to the subfloor.
You can use a specialist Click Lock or a good-quality contact adhesive. Before you start to tile, make sure you have a suitable underlay. This will help to protect your subfloor and reduce noise.
Installing Click Lock Tiles in a Straight Line
When installing tiles in a straight line, you must assemble them and click lock. Begin by measuring and marking the tiles to ensure they are the correct length.
The easiest way to do this is to place a tile on the floor and mark the length using a pencil. Then, lay the tile on another tile and mark the length again. You will notice that the tile that is on top is much longer than the one underneath. Measure the gap between the two tiles and add a few extra millimeters to this measurement.
This will account for the tiles shrinking as the adhesive cures. Mark the tiles at the new measurement, and then you can use a suitable adhesive to attach the tiles. The tiles should be connected within 24 hours to ensure the adhesive cures correctly.
Installing Click Lock Tiles in an Invisible Corner
To install Click Lock tiles in an invisible corner, you must first mark one tile at each end of the corner. Next, place one marked tile against the wall with the correct side facing down.
Place a second marked tile on the other side of the wall and click lock the two tiles together. You can now place the third marked tile on top and click lock it together.
You can now place the other two tiles next to the wall and click lock them together similarly. If the tiles are not fitting together correctly, you can tap the corner with a hammer to ensure the edge is lined up correctly.
Installing Beveled Edge Tiles
Beveled edge tiles cover the edges of wooden or laminate floors. These tiles have a beveled outer edge designed to sit just below the level of the adjoining flooring. Begin by measuring the length of each edge of the flooring with a tape measure.
Then mark the tiles at the same length but without the width of the locking strip. Once you have marked the tiles, use a suitable adhesive to glue the tiles down.
Can I Install Click And Lock Flooring Myself?
It is easy to install click and lock flooring. You don’t need any special tools or skills to do it. The click and lock system makes it easy to install. You only need a few tools mentioned above. You can install click and lock flooring in a day or two, and you don’t need any experience. Of course, the installation duration depends on the size of the room.
After you install click and lock flooring, you are not done. You will need to maintain the flooring to keep it looking nice. The click and lock system makes maintenance easy, too.
How to Install Click Lock Flooring on Concrete
1. Clean the concrete
Before you begin, ensure your concrete is clean and free of debris. This will help ensure that your flooring adheres appropriately and lasts many years.
2. Gather Required Tools
You’ll need a few tools to install your click lock flooring, including a straight edge, a utility knife, and a hammer.
3. Start Measuring
Once your tools are ready, start by measuring the area where you’ll be installing the flooring. It’s essential to be precise when measuring and cutting the flooring pieces, so take your time and double-check your work before moving on to the next step.
4. Cut Your Flooring
Cut your flooring to size using the straight edge and utility knife, then fit it into place. You may need to trim some of the pieces to get them to fit perfectly in your space.
5. Tap The Flooring pieces
Use the hammer to tap the flooring pieces together until they snap into place. Be careful not to overdo it, or you could damage the flooring pieces.
6. Enjoy
You’re now ready to enjoy your new click lock flooring! Thanks for following along with us today. We hope this blog post was helpful and that you’re now feeling confident about tackling this project yourself.
Conclusion
When installing Click Lock flooring, the key is to take the time to mark everything carefully, follow the manufacturer’s instructions, and use the correct tools. The tiles will lock together quickly and will create a beautiful new floor.
